![spine2d white space around images spine2d white space around images](https://www.pica8.com/wp-content/uploads/new-image-for-leaf-spine-page-051120.jpg)
It’s hard for me to believe that using the same measurement no matter what page it’s on or how many pages there are will provide satisfactory results. Another will give me a number but won’t promise that it will work. One says to just make an educated guess as to how much to bump the images left/right because the amount changes with where it is in the book. In my experience with perfect bound magazines, the printers vary widely on this topic. I don’t know if this makes a difference or not, but the magazine has a print run of between 90,000 and 100,000 copies and ranges from 164 to 212 pages. This is the only occurrence that our printer says don’t do anything and just give us normal, single page PDFs and we’ll work the magic at our end. You mention a cross-over between the inside cover and the first/last page of the book. The printer did mention that not all their clients go to this trouble, but they would prefer it if they did.Ībout a year ago, we produced a special edition of the magazine which was printed overseas (our normal printer is in Australia, the special edition was printed in China) and they gave me exactly the same requirements about splitting pics across the spine as the printer here wants. Last time I specifically asked them about it, they asked me to still carry on doing what I was doing. I haven’t spoken to the printer about this setup for a few years, but they’ve also never told me to stop doing it. We’ve been producing this magazine for about 9 years now. These were verbal specs from the printer that took us a few phone calls to clear up, as we were given different instructions from the art director when we took on the job. These crossovers are the hardest to line up.
SPINE2D WHITE SPACE AROUND IMAGES SOFTWARE
So in short, no, I don’t do this – I let my imposition software move the pages to where they need to be for the appropriate binding… About the only time I might consider something like this is a cross-over between an inside cover and the first/last page of the book, and its to compensate for the 3-5mm of glue that bind the first/last page to the cover of the book. That said, having crossover images on a perfect bound book will have issues if the reader has to force the pages apart to see any content that may be hard to see in the bind… and this may be another reason the printer has suggested this 3mm offset towards the foredges. If the book was printed digitally onto a smaller sheet size so that no folding is necessary, and book blocks are just one set of guillotine trims, then an even smaller gutter can be allowed for. If it was printed in large sections that are folded to the trim size and then the collected gathered folded signatures are then ground flat, then a gutter is normally allowed in the spine to compensate for the spine being ground down… otherwise the finished art will always be smaller than expected… unless the art is being overtrimmed at the end. Do you have the mechanical specs from your printer that state this, or are these verbal instructions that were given by the printer at one stage… and have you asked the printer about this lately?ĭepends how the book was printed. I paid him to write it for me about 7-8 years ago and I have been using it ever since. The guy that wrote my script can be contaced at: ĭisclaimer: I don’t know the guy. Is there another way to do this without a script or does everyone do it manually, or do people not bother splitting the pics anymore?
![spine2d white space around images spine2d white space around images](https://images.squarespace-cdn.com/content/v1/5cbc947ead02610001a2c6b4/1591047137532-JFSA0DDCFLV5QF3VNGUL/image-asset.jpeg)
I occasionally look to see if there are any other solutions, but I am surprised that I never seem to find any. I ended up getting a guy to write a custom script for me, which does all of those steps, which saves me heaps of time. I looked around for a lazy solution, but couldn’t find one. I assume it’s the same for everyone that produces perfect bound magazines. Make sure you haven’t covered over anything in the original duplicate process. Select the picture inside the frame on the right page and move it inside the frame by 3mm to the right.Ħ. Select the picture inside the frame on the left page and move it inside the frame by 3mm to the left.ĥ. Drag the left side of the frame on the right page to the spine.Ĥ. Drag the right side of the frame on the left page to the spine.ģ. Duplicate the picture box on top of itself.Ģ. For the perfect bound magazine that we produce, the printer requires us to split pictures that go across the spine to allow for the grind.ġ.